View MC10H334-D_525858.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC10H334
Quad Bus Driver/Receiver with Transmit and Receiver Latches
The MC10H334 is a Quad Bus Driver/Receiver with transmit and receiver latches. When disabled, (OE = high) the bus outputs will fall to -2.0 V. Data to be transmitted or received is passed through its respective latch when the respective latch enable (DLE and RLE) is at a low level. Information is latched on the positive transition of DLE and RLE. The parameters specified are with 25 loading on the bus drivers and 50 loads on the receivers. * Propagation Delay, 1.6 ns Typical Data-to-Output * Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range) * Voltage Compensated * MECL 10K-Compatible
DIP & PLCC PIN ASSIGNMENT
VCC BUS1 BUS0 VCC02 D1 D0 DLE R0 R1 VEE 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCC03 BUS2 BUS3 OE D2 D3 RLE R3 R2 VCC02 A WL YY WW = Assembly Location = Wafer Lot = Year = Work Week
http://onsemi.com MARKING DIAGRAMS
20 CDIP-20 L SUFFIX CASE 732 1 20 PDIP-20 P SUFFIX CASE 738 1 1 PLCC-20 FN SUFFIX CASE 775 10H334 AWLYYWW MC10H334P AWLYYWW MC10H334L AWLYYWW
ORDERING INFORMATION
Device MC10H334L MC10H334P MC10H334FN Package CDIP-20 PDIP-20 PLCC-20 Shipping 18 Units/Rail 18 Units/Rail 46 Units/Rail
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 18 of the ON Semiconductor MECL Data Book (DL122/D).
NOTE: Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained. Receiver outputs are terminated through a 50-ohm resistor to -2.0 volts dc. Bus outputs are terminated through a 25-ohm resistor to -2.0 volts dc.
(c) Semiconductor Components Industries, LLC, 2000
1
March, 2000 - Rev. 6
Publication Order Number: MC10H334/D
MC10H334
MAXIMUM RATINGS
Symbol VEE VI Iout TA Tstg Power Supply (VCC = 0) Input Voltage (VCC = 0) Output Current - Continuous - Surge Operating Temperature Range Storage Temperature Range - Plastic - Ceramic Characteristic Rating -8.0 to 0 0 to VEE 50 100 0 to +75 -55 to +150 -55 to +165 Unit Vdc Vdc mA C C C
ELECTRICAL CHARACTERISTICS (VEE = -5.2 V 5%) (See Note)
0 Symbol IE IinH Characteristic Power Supply Current Input Current High Pins 5,6,15,16 Pins 7,14 Pin 17 Input Current Low High Output Voltage Low Output Voltage High Input Voltage Low Input Voltage Min - - - - 0.5 -1.02 -1.95 -1.17 -1.95 Max 161 397 460 520 - -0.84 -1.63 -0.84 -1.48 Min - - - - 0.5 -0.98 -1.95 -1.13 -1.95 25 Max 161 273 297 357 - -0.81 -1.63 -0.81 -1.48 Min - - - - 0.3 -0.92 -1.95 -1.07 -1.95 75 Max 161 273 297 357 - -0.735 -1.60 -0.735 -1.45 A Vdc Vdc Vdc Vdc Unit mA A
IinL VOH VOL VIH VIL tpd
AC PARAMETERS
Propagation Delay Data-to-Bus Output DLE-to-Bus Output OE-to-Bus Output Bus-to-R0 RLE-to-R0 Data-to-Receiver R0 Rise Time Fall Time ns 0.5 1.0 0.5 0.5 0.5 1.0 0.5 0.5 2.5 2.7 2.5 1.9 2.1 3.8 2.2 2.2 0.5 1.0 0.5 0.5 0.5 1.0 0.5 0.5 2.5 2.7 2.5 1.9 2.1 3.8 2.2 2.2 0.5 1.0 0.5 0.5 0.5 1.0 0.5 0.5 2.5 2.7 2.5 1.9 2.1 3.8 2.2 2.2 ns ns
tr tf
http://onsemi.com
2
MC10H334
LOGIC DIAGRAM
17 7 6 5 16 15
OE DLE D0 D1 D2 D3 G D D D D Q Q Q Q BUS0 BUS1 BUS2 BUS3 3 2 19 18
14 8 9 12 13 10 1 4 11 20
RLE R0 R1 R2 R3 VEE VCC VCC01 VCC02
OUTPUT LATCH
G Q Q Q Q D D D D
RECEIVER LATCH
DRIVER TRUTH TABLE
D X DLE X L H OE H L L Busn+1 -2.0 V D Busn
RECEIVER TRUTH TABLE
Bus Bus X RLE L H Rn+1 Bus Rn
VCC03
D X
http://onsemi.com
3
MC10H334
PACKAGE DIMENSIONS
PLCC-20 FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C
B -N- Y BRK D -L- -M- W D X V A Z R 0.007 (0.180) M T L-M
S
0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
Z
20
1
G1
0.010 (0.250)
S
T L-M
S
N
S
VIEW D-D 0.007 (0.180) M T L-M
S
N N
S
H
0.007 (0.180) M T L-M
S
N
S
S
K1 K
C
E 0.004 (0.100) G G1 0.010 (0.250) S T L-M J -T-
SEATING PLANE
F VIEW S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
0.007 (0.180) M T L-M
S
N
S
VIEW S
S
N
S
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
http://onsemi.com
4
MC10H334
PACKAGE DIMENSIONS
CDIP-20 L SUFFIX CERAMIC DIP PACKAGE CASE 732-03 ISSUE E
20 1
11 10
NOTES: 1. LEADS WITHIN 0.010 DIAMETER, TRUE POSITION AT SEATING PLANE, AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSIONS A AND B INCLUDE MENISCUS. INCHES MIN MAX 0.940 0.990 0.260 0.295 0.150 0.200 0.015 0.022 0.055 0.065 0.100 BSC 0.020 0.050 0.008 0.012 0.125 0.160 0.300 BSC 0_ 15_ 0.010 0.040
B A F C L
DIM A B C D F G H J K L M N
N H D
SEATING PLANE
G
K
J M
-A-
20 11
PDIP-20 P SUFFIX PLASTIC DIP PACKAGE CASE 738-03 ISSUE E
B
1
10
C
L
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01
-T-
SEATING PLANE
K M E G F D
20 PL
N J 0.25 (0.010)
M 20 PL
0.25 (0.010) TA
M
M
TB
M
DIM A B C D E F G J K L M N
http://onsemi.com
5
MC10H334
Notes
http://onsemi.com
6
MC10H334
Notes
http://onsemi.com
7
MC10H334
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 2:30pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 2:30pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 1:30pm to 5:00pm UK Time) Email: ONlit@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: r14525@onsemi.com Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
8
MC10H334/D

▲Up To Search▲

Price & Availability of MC10H334-D

	To Download MC10H334-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .